Menu
Your Cart
Log in to LOWER your prices.

Doming Starter Kit

Hot Back Order 2-4 weeks
No Minimums required. Available Blank (for you to Print), or Printed with your artwork ready to sell.

Guide to ProCut Vinyl Cutter Models

*If link to 'Your' Cutter Not Shown - Please Ask
Opening Size
Saga Contour
Saga Contour
Saga Contour
Saga Precision
Saga Precision
Saga Precision
12 inch
420II
420IIP
-
-
-
15 inch
490I
490II
490IIP
P490I
P490II
P490IIP
24 inch
P720I
P720II
P720IIP
48 inch
P1350I
P1350II
P1350IIP
64 inch
-
1750IIP
-
P1750II
Motor Type
Stepper
Servo
Servo
Stepper
Servo
Servo
Contour Cutting
Laser Dot
Laser Dot
ARMS
Laser Dot
Laser Dot
ARMS
DragonCut
Yes
Yes
Yes
Yes
Yes
Yes
SignCut
Yes
Yes
Yes
Yes
Yes
Yes
Flexi
Yes
Yes
Yes*
Yes
Yes
Yes*
Mac
Yes
Yes
Yes
Yes
Yes
Yes
PC
Yes
Yes
Yes
Yes
Yes
Yes
Cuts - Vinyl
Yes
Yes
Yes
Yes
Yes
Yes
Cuts - T-Shirt Vinyl
Yes
Yes
Yes
Yes
Yes
Yes
Cuts - Sand Mask
No
Yes
Yes
No
Yes
Yes
Cuts - Window Tint
Yes
No
No
Yes
No
No
THIS PRODUCT INCLUDES A 5 YEAR WARRANTY
Doming Starter Kit
doming starter kit

epoxy resin doming kit

Ideal for 'clear 3d doming'

Epoxy resin doming kit

Product #: Doming Kit
Retail price: $149.00 Our Price
$134.00
Available from: The Laughing Professor
Condition:
NEW, in excellent condition
In stock! Order now!

ready to ship now
* Available - refills and extras
Join our Facebook Group and stay upto date with NEW products and Stock (also Special Pricing available on many Products).

Doming Starter Kit, epoxy resign doming kit
Doming is a process of applying a clear resin coating to any vinyl graphic or coated label. It gives the graphic an eye-popping, 3-D effect, enhancing any sign or logo and attracting more attention to your product. It improves and protects any graphic image you apply it to. Our Doming cartridges are 75g - 50% larger than many of our competitors.
Each cartridge covers approximately 80 sq. inches.

The resin is U.V. stable, outdoor durable, non-yellowing, and semi-flexible.
2 - 75g ProDome Resin Cartridges
4 - 75g ProDome Mixers
1 - ProDome Applicator Gun
1 - Bubble Remover Torch (lighter fuel not included)

Instructions



Accessories and spare also available separately: mixer tubes pack of 10 $21.99 and 1 Cartridge + 2 mixer tuber $29.00


INSTRUCTIONS:-
Step One
Prepare application gun. Be sure the plunger is fully retracted (As shown).
Open clip in front of gun.

Step Two
Remove one cartridge from package. Slide the cartridge through the front
clip. Close the clip by pulling the cartridge up until it clicks.

Step Three
Unpack one acudome mixer. Remove the cartridge cap by twisting 90
degrees anti-clockwise and pull to separate. Also, the rubber seal may
stick to cartridge under the cap, remove seal, pull off slowly. Attach
mixer to cartridge by twisting the mixer into the grooves on the cartridge
90 degrees clockwise.

Step Four
Hold gun at a 45 degree angle to allow bubbles to rise to the top of
cartridge. Hold purge cup at the end of the mixer keeping cartridge
pointing upward while pulling trigger to purge about 3ml-5ml of the
resin to make sure it’s mixed well. Make sure there are no bubbles.
Apply resin to vinyl at a slow comfortable rate. Applying Acudome Fast
will cause it to not mix correctly!

Step Five
After 2-3 minutes the resin should flow to the outside edge of your graphic,
if not add a couple more drops of resin. If resin still has not flowed to
corners you can use your repair tool to push resin slowly to the edge.

Step Six
After leaving the decal for 5 minutes, if there are any bubbles a quick
flash with the bubble remover should remove them. Do not leave flame
on. Just a quick flash. If bubbles do not come out place repair tool into
resin and move around to bring bubble to top surface. Then do another
quick flash with the bubble remover. If resin has run off decal. Let resin
set for 5-6 minutes. Then with repair tool scrape alongside of decal
scraping resin away from decal. The resin will reseal itself. It takes 12
hours to touch, 48 hours to ship putting wax paper between them and
if you are applying decals to car, truck or boat let it cure for at least
6 days before applying.

Removing bubbles
Remember removing bubbles only requires one click from your bubble
remover.... Hint: If you have some left over resin after your project is
complete. Dome some samples to provide to customers who are
interested in your domed decals !!! Also, remember to have fun..




We are able to create that very special and unique gift with any design, corporate logo or photo. Upload your unique idea/design and have your very own special, one of a kind made just for you.

COPYRIGHT.
Work accepted by The Laughing Professor is on the specific understanding that under Title 17 US Copyright Code the client undertakes that he/she has obtained the copyright release or license for material submitted and will indemnify The Laughing Professor against any breach of the law. An order accepted by The Laughing Professor is on the understanding that the client assumes liability for any resulting violation of copyright in any action brought by a third party.
Laughing professor Website Home page. Professors Blog Our Business Facebook Page google plusYoutube our Linkedin Page InstagramOur Twitter pageebay
Mix-n-Match any Designs with any of our Items * Businesses Site & Login :- Wholesale.LaughingProfessor


|© Copyright 1996 - 2019 The Laughing Professor
|Business Address: 1779 Joe Frank Harris Pkwy SE, Cartersville, Georgia,30120, USA
|Tel: +1 470-233-0626 |Email: Paul@laughingprofessor.net.
|Business hours are

Write a review

Please login or register to review
  • Stock: Back Order 2-4 weeks
  • Model: Dome Kit
  • Weight: 1.16lb
  • Shipping Size: 8.00in x 8.00in x 8.00in
  • MPN: PD-TIK
904 sold
$134.00
PRIORITY Notification.
LOG IN to LOWER your PRICES. *Check your 'Account Type'